Search:

Type: Posts; User: Silent Scone@ROG

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Hello, Did you enable DOCP prior to the issue...

    Hello,

    Did you enable DOCP prior to the issue occurring?


    1. Turn off the computer and unplug the power cord

    2. Locate CLRTC pins as per snip below

    3. Short circuit the pins with a...
  2. Replies
    4
    Views
    178

    Hello, You've not posted in the correct...

    Hello,

    You've not posted in the correct section at all which hasn't helped you in getting any replies.

    error 41 is fairly generic and is synonymous with a lot of system crashes.

    Does the...
  3. Hi, You've not mentioned which software you're...

    Hi,

    You've not mentioned which software you're referring to? If it's third party such as HWInfo, you're best off asking the author.
  4. The iCUE uninstallation could be a red herring,...

    The iCUE uninstallation could be a red herring, hard to say. Reset the UEFI and go from there.
  5. Replies
    3
    Views
    105

    Hello, Really depends on your budget and the...

    Hello,

    Really depends on your budget and the capacity needed.

    GSKILL Neo kits are still one the best options due to GSKILL's vigorous hand binning. Look for anything in the 3400-3666 range....
  6. Hello, What did you adjust in the BIOS...

    Hello,


    What did you adjust in the BIOS prior the problem starting? Have you tried to reset the UEFI via the rear I/O panel?
  7. Hello, Devcon is the driver handoff console,...

    Hello,

    Devcon is the driver handoff console, and that message can sometimes be related to the driver being incompatible with the OS version.

    Try from here:...
  8. Hello, Despite it happening in both operating...

    Hello,

    Despite it happening in both operating systems I would be tempted to install a fresh dummy OS on a separate drive and see if the problem persists there. A failing PSU will often result in...
  9. Replies
    5
    Views
    192

    No worries, will pm.

    No worries, will pm.
  10. Yes, the vcore is normal. Flash to the latest...

    Yes, the vcore is normal. Flash to the latest UEFI if looking for the latest AGESA from AMD
  11. Hi, please respond to the other thread as have...

    Hi, please respond to the other thread as have asked for Q-Code received.
  12. Was replying to the post above. 5K is tough. Hard...

    Was replying to the post above. 5K is tough. Hard to say when not comparing sub timings. Q-Code should should help determine where to to start looking.
  13. Hello, This is normal behaviour for Ryzen...

    Hello,

    This is normal behaviour for Ryzen Precision Boost upward of up to 1.5v The CPU needs this much voltage in some instances to maintain frequency and adapts to high current loads accordingly.
  14. What Q-Code? The common denominator is likely...

    What Q-Code?
    The common denominator is likely using a previous generation CPU on a next gen board. Optimisations and auto rulings when pushing limits to the very edge as you are doing are often with...
  15. Remove AI Suite then reset the UEFI to optimised...

    Remove AI Suite then reset the UEFI to optimised defaults.
  16. Hi, if you don't use AI Suite for anything other...

    Hi, if you don't use AI Suite for anything other than 5 way, I would recommend removing and let the board control boost behaviour on its own.
  17. You can enable Fast boot to avoid retraining the...

    You can enable Fast boot to avoid retraining the memory, this should decrease POST time.

    Be sure to try both XMP profiles 1 and 2. Often, XMP II timings will be slightly looser depending on the...
  18. Replies
    5
    Views
    192

    Thanks for that. Can you give me your...

    Thanks for that.

    Can you give me your specification and upload a DXDIAG, please? (Type Dxdiag into Windows Search, open DXDIAG and click save information)

    Have you changed anything since the...
  19. Depends largely on the workload and may impact...

    Depends largely on the workload and may impact your single threaded performance, but these chips can benefit from undervolting. You'd need to test performance for your use case.
  20. CPU-Z Displays the VID which represents the...

    CPU-Z Displays the VID which represents the voltage the CPU believes it's receiving. Use HWInfo or a suitable monitoring tool to monitor the Vcore.


    On the Apex you may want to try running...
  21. Hello, Which board, CPU? It's always best...

    Hello,

    Which board, CPU?

    It's always best to use the UEFI where possible to reduce system overhead.
  22. Replies
    5
    Views
    192

    Can you show which ports on the board don't...

    Can you show which ports on the board don't appear to be working?
  23. BIOS revision 3801 contains the latest 1.2.0.2...

    BIOS revision 3801 contains the latest 1.2.0.2 AGESA. Unless experiencing any problems there's no reason to downgrade.
  24. Replies
    2
    Views
    206

    Hello, I've moved your post to the correct...

    Hello,

    I've moved your post to the correct section for you.

    GPUT3 is currently in beta which is clearly stipulated. This means that it is in a pre-release phase. You can join the beta...
  25. Hello, The package temperature represents the...

    Hello,

    The package temperature represents the average core temperature as reported by the internal sensors over a predefined period
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4