Search:

They are not official from Asus nor are from Asus.

I wouldn't update. The latest version in this post is faulty and you can't go back once you've flashed it. It will make some settings unavailable on your board, like BCLK, Max core Temp and possibly...

That is a very old version of the Intel CSME detection tool you are using. The current one is 7.0.1.0 (there may be even newer, I did not check). To check against newer vulnerabilities, you have to...

I'd check my other memory settings first. I often forget to enter a setting when upgrading to a new bios. Is the memory OC mode the same for example?
Anyhow, good luck. It is a pita.

Try manual setup of 4000 instead of XMP using the XMP values of cas, trcd, tras tfaw, trrd_s/_l

I was running 4000 16-16-34 very with tight timings and 1.17v/1.19v vccio/vccsa on my 2x16...

Thunderbolt (and USB ports) charge my iphone fine when the PC is in sleep mode.

For USB at least, there is a BIOS configuration option to provide USB power in the soft-off state.

Hi, @Shamino or other Asus Engineers

I am having 3 problems with my Hero XIII. I have a 10900k in it.

1. Random Static popping with the on-board Audio. I have worked around this using an...

Updated from 2403. Seems fine so far.

According to the MB spec, it comes with:

1 x M.2 SSD screw package(s). It is not held down by the MB heatsink screw. You'll need a standoff between the motherboard and the screw if one...

I don't see at all how this is Asus fault at all. They did not provide or publish this firmware, so they did not test it on their boards, or did and found issues with it so did not publish it. The...

I don't seem to be able to change the BCLK in BIOS to anything other than 100 MHz without boot looping either.

I would stay well away form this version. It has serious issues.

Asus BIOS is set up to not allow the Intel Management Engine region to be overwritten with a BIOS update.
In addition, Intel does not allow you to flash ME firmware with older versions ...

I believe you have to disable secure boot and reboot in order to enable CSM.

Not offhand, sorry

Did you try resetting the CMOS ? That should boot it up with default settings

Read back a few posts in this thread. You are not the first and there is a workaround.

Have you flashed 14.1.65.1969? There are some issues with it, but they can be worked around. I tried to roll back to 14.1.53.1649 and it was not permitted.

I use the intel MEInfo tool:


Intel(R) ME code versions:
BIOS Version 2403
GbE Version 0.4
Vendor ID ...

Asus has an AIsuite 3 cleaner tool that might help. Should be under Software and utilities on their web support page, Haven't tried it myself.

Some BIOS version back I noticed this behavior with the Maximum current setting. If you lower it enough below it's maximum value, the board behaves according to Intel specs, so even all-core...

I had the same issue. Boot loop with anything besides default.
Just to make sure the firmware posted here was not busted, I built it from the modules at Win-raid myself. Still same issue. ...

The Vanatoo are pretty decent for the space they take. I have the original, not the encore. It looks like the difference is the remote control .

:rolleyes:

I have been running it since October without issue too. TPM is required for Windows 11 so I think it was driven by over-zealous marketing people so they could say it is Windows 11 ready. It doesn't...

You can put caps on how high the automatic voltage for core, vccio, and vccsa can go. There is a section in the BIOS for that. If your doing automatic on any of these, I highly recommend it. 1.45...