Search:

Type: Posts; User: Silent Scone@ROG

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Hello, It might help to show us a picture of...

    Hello,

    It might help to show us a picture of your setup and mention the ambient temperature. I have moved your post to the support section.
  2. Sounds like a bad flash. Could be due to a number...

    Sounds like a bad flash. Could be due to a number of things, including system instability. Glad you were able to use flashback.
  3. You are far better off looking for the highest...

    You are far better off looking for the highest obtainable frequency at Command Rate 1.
  4. Replies
    4
    Views
    465

    Hello, Yes the latest version of the drivers...

    Hello,

    Yes the latest version of the drivers is likely the best option, it's also wise to use these if experiencing any of AMD's USB drop out problems when paired with a PCIE 4.0 enabled GPU.
  5. Replies
    14
    Views
    370

    Hello, If you happen to have access to enough...

    Hello,

    If you happen to have access to enough CPU samples to conclude 1.25v is safe for SOC then feel free to continue on that adventure. AMD doesn't offer it's own guidance, however this much...
  6. Hello, One would need to have tested a CPU...

    Hello,

    One would need to have tested a CPU sample size large enough before making statements for or against, or have access to that information

    1) CPU variance is indeed a factor, not all CPU...
  7. Replies
    14
    Views
    370

    Best to state this in future! ;) If testing a...

    Best to state this in future! ;)

    If testing a CPU sample methodically there will be drop off points where the system will become unstable, meaning more voltage is worse. The three samples I have...
  8. Replies
    14
    Views
    370

    Hello, As above, 1.2 to 1.25v is...

    Hello,

    As above,



    1.2 to 1.25v is excessive and can potentially degrade the CPU, so this is poor tuning advice. No more than 1.15v should be needed if tuning correctly for daily use.


    As...
  9. Replies
    14
    Views
    370

    Hello, Values of up to 1.15v are fine,...

    Hello,

    Values of up to 1.15v are fine, exceeding this should not be necessary on majority of CPU.
  10. Hello, This is official support for JEDEC 3200...

    Hello,

    This is official support for JEDEC 3200 and doesn't include overclocking.


    The Dark Hero will do 4000MHz no problem, however, not all CPU will be able to run FCLK at 2000MHz...
  11. Replies
    62
    Views
    15,094

    The official service post can be found here on...

    The official service post can be found here on the support portal: https://www.asus.com/us/support/FAQ/1046215
  12. No worries. Vcore fluctuation behaviour is...

    No worries.

    Vcore fluctuation behaviour is normal when changing p states. As mentioned before, most RGB effects for example beyond static are often enough to elevate p states.
  13. Hello, Obviously this will depend on the...

    Hello,

    Obviously this will depend on the changes between UEFI builds. The consensus, unfortunately, over the last couple of years is that performance is worse due to the barrage of ucode security...
  14. The other thing to make sure of is if the system...

    The other thing to make sure of is if the system is actually idle. With the way cores are loaded up on these CPU, it doesn't take much load to impact the temperature when compared to Intel variants....
  15. Replies
    2
    Views
    186

    The FCLK(Fabric Clock) and memory should be run...

    The FCLK(Fabric Clock) and memory should be run in a 1:1 ratio in order to obtain the lowest latency, yes. On majority of UEFI builds FCLK should sync to the memory speed, however, you can sync it...
  16. Hello, Regardless of setup, temps,...

    Hello,

    Regardless of setup, temps, specifically idle, can be higher than what some users are normally used to on other platforms due to how Zen handles idle core states. Undervolting Zen can be...
  17. Have moved to support section.

    Have moved to support section.
  18. Hello, Have you tried adjusting the VCCSA...

    Hello,

    Have you tried adjusting the VCCSA voltage?

    Try values between 1.2 - 1.35v.
  19. Replies
    2
    Views
    225

    Hello, To begin with you'd need to remove...

    Hello,


    To begin with you'd need to remove XMP/DOCP in order to revert the system to stock. If the issue no longer persists you'll have your answer about the memory being the culprit.
  20. It largely depends on ambient/case temperatures,...

    It largely depends on ambient/case temperatures, but 65c is well within operating range. So, yes, everything is ok.
  21. Hello, Do you receive a CPU Over Temp error...

    Hello,

    Do you receive a CPU Over Temp error upon rebooting? The UEFI will put some load on the CPU intentionally.
  22. Replies
    62
    Views
    15,094

    thread stickied.

    thread stickied.
  23. Hello, Post moved to ROG Care. Reset...

    Hello,


    Post moved to ROG Care.



    Reset the UEFI via the rear IO button and then cycle the AC by turning off at the mains.
  24. It's great when it shows up after a few weeks,...

    It's great when it shows up after a few weeks, too ;)
  25. The memory wasn't stable enough to pass training....

    The memory wasn't stable enough to pass training. 0d is a training error, you can try increasing VDIMM if wanting to dial back latency
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4