Search:

Type: Posts; User: Silent Scone@ROG

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. It's great when it shows up after a few weeks,...

    It's great when it shows up after a few weeks, too ;)
  2. The memory wasn't stable enough to pass training....

    The memory wasn't stable enough to pass training. 0d is a training error, you can try increasing VDIMM if wanting to dial back latency
  3. Hello, I've moved the original thread to ROG...

    Hello,

    I've moved the original thread to ROG care.
  4. Replies
    9
    Views
    677

    The strength of the IF depends on the CPU sample....

    The strength of the IF depends on the CPU sample. If you're comparing two different CPUs across two different builds, that's going to bring up the disparity you're experiencing
  5. Hello, Remove the CPU, check for any bent...

    Hello,

    Remove the CPU, check for any bent pins. Remount cooling whilst checking for even mounting pressure. You may wish to try outside of the chassis, too.
  6. Replies
    1
    Views
    239

    Hello, Current is the biggest contributing...

    Hello,

    Current is the biggest contributing factor to degradation, so idle voltage plays a minimal role in this process.

    Static or "fixed" voltage vs Adaptive will not noticeably impact the life...
  7. Replies
    9
    Views
    677

    Hello, The fabric itself and it's behaviour...

    Hello,

    The fabric itself and it's behaviour will remain static between builds. System stability can change, however. Especially between AGESA builds, or if the condition of the overclock was...
  8. Replies
    4
    Views
    132

    The real question is what makes you need a new...

    The real question is what makes you need a new system right now?

    Personally speaking as of this moment, I would not make the switch till Alderlake. Then decide on which path you wish to take....
  9. You may wish to experiment with VSOC. Try values...

    You may wish to experiment with VSOC. Try values between 1.08v and 1.15v

    VDIMM try 1.45v
  10. Hello, That kit may well be certified for 4K,...

    Hello,

    That kit may well be certified for 4K, but not on that platform.

    128GB will be very tough on the Infinity Fabric. How much VSOC have you tried for 3200MHz?
  11. Hello, Depending on the values set, platform...

    Hello,

    Depending on the values set, platform and which board, the auto voltages scale based on worst case scenarios for CPU sample strength. You can tune these values manually to best suit your...
  12. Replies
    2
    Views
    215

    Hello, The GPU Boost Clock and available...

    Hello,

    The GPU Boost Clock and available offset merely sets the maximum target frequency. The actual frequency under load is controlled by GPU Boost and will scale based on voltage, power, and...
  13. This has less to do with the number of ranks. The...

    This has less to do with the number of ranks. The memory density puts the most strain on the Fabric, thus the CPU sample is important.
  14. Hello, Would need more context. I've not had...

    Hello,

    Would need more context. I've not had any issues running 4 modules on the Crosshair 8 Hero up to 3800 with my current 5950X or my previous 3950X. Your question is more attributed to 64GB at...
  15. Replies
    8
    Views
    347

    Who knows, it's possible something was stuck at...

    Who knows, it's possible something was stuck at driver level or was tripping GPUZ into think it wasn't enabled. Glad you got it working!
  16. Replies
    8
    Views
    347

    Not that it should make much difference, but are...

    Not that it should make much difference, but are you using a PCIE riser or is the card connected directly?

    Check in the UEFI that 4G decoding is enabled. Although the toggle on the landing page...
  17. 4x8GB 4266 on the Formula and 9900K. All sub...

    4x8GB 4266 on the Formula and 9900K. All sub timings board controlled with XMP profile enabled.

    88791
  18. Hello, 1) It's best to tune to the maximum...

    Hello,

    1) It's best to tune to the maximum obtainable ratio at CR1

    2) Anything beyond 3800-3866 will need to be ran at CR2

    3) ROG Z390 boards are all T-Topology which means the board works...
  19. Replies
    8
    Views
    347

    Hi Hopper, What's the status say in the top...

    Hi Hopper,

    What's the status say in the top right in UEFI? Should be able to toggle it there.
  20. Not on this board at those frequencies, no. I've...

    Not on this board at those frequencies, no. I've limited experience on that particular platform but Gear 2 will likely be needed for anything beyond 3866 at 1T on that board
  21. Replies
    7
    Views
    252

    Can appreciate the curiosity, but unless someone...

    Can appreciate the curiosity, but unless someone has done this groundwork already this behaviour is difficult to observe. Even by Buildzoids admission in some of his videos, the probes and scope...
  22. Replies
    7
    Views
    252

    I'm not aware of what level is set by default,...

    I'm not aware of what level is set by default, unfortunately. If you're aware of the function then knowing in which direction the loadline works is really all you should be concerned with.

    There...
  23. Hello, What is the Q-CODE displayed? If...

    Hello,

    What is the Q-CODE displayed?


    If the system is sometimes able to pass POST then the stability is borderline. Try increasing SOC voltage if not having done so already.
  24. As above, then. Power cycles are normal ...

    As above, then. Power cycles are normal depending on the board and controllers present.

    If there are multiple cycles then it does sound like memory training.

    Return the system to optimised...
  25. Continuous cycles sounds like training failure,...

    Continuous cycles sounds like training failure, the memory isn't stable.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4