Search:

Type: Posts; User: IMweasel

Page 1 of 2 1 2

Search: Search took 0.00 seconds; generated 50848 minute(s) ago.

  1. Sticky: Looking for a place to order the EK waterblock...

    Looking for a place to order the EK waterblock for the Crosshair V F-Z...in Europe...can it be obtained here somewhere?
  2. Hi, when enabling the EPU in BIOS, you should try...

    Hi, when enabling the EPU in BIOS, you should try all it´s sub-options. Min/med/max power saving.
    it´s about enabling the energy processing unit in various ways,to see if less power on the vrm´s...
  3. Sure you didn't touch anything else unmentioned?...

    Sure you didn't touch anything else unmentioned?

    Tune the EPU a bit, try all other settings besides auto.

    If you cannot hold certain parts because of the temperature,it's safe to say that part...
  4. Well lets try it like this; IBT stress test it...

    Well lets try it like this; IBT stress test it for a while on max setting...
    Can you touch the area on the back of the board where the VRM's are located? Without it hurting of the area being too...
  5. P-State FID 0x1F - VID 0x01 - IDD 18 (25x -...

    P-State FID 0x1F - VID 0x01 - IDD 18 (25x - 1.537 V)
    P-State FID 0x1F - VID 0x01 - IDD 18 (23.50x - 1.537 V)
    P-State FID 0x1D - VID 0x01 - IDD 18 (22.50x - 1.537 V)
    P-State FID 0x18 -...
  6. You´re welcome. I haven´t experienced something...

    You´re welcome. I haven´t experienced something like this in my whole life, and i´m not sure if this is the right approach.
    It´s low risk though, i cannot predict the outcome but it´s not harmful...
  7. I´m currently preferring the second setup ATM!

    I´m currently preferring the second setup ATM!
  8. Make sure that airflow is going over the VRM...

    Make sure that airflow is going over the VRM heatsinks,and mount a fan on the back of the board to cool the VRM's extra. It definately helps to maintain stability under load.
    Make sure that all...
  9. Make sure that airflow is going over the VRM...

    Make sure that airflow is going over the VRM heatsinks,and mount a fan on the back of the board to cool the VRM's extra. It definately helps to maintain stability under load.
    Make sure that all...
  10. So uhm, after the AMD 170U was in the CH5FZ, did...

    So uhm, after the AMD 170U was in the CH5FZ, did you move it back to the CH5F? And it failed too?
    Still thinking about this case!
    edit:
    I stick to bios corruption. I think it has to do with the...
  11. Could be worth the try to use this spare cpu......

    Could be worth the try to use this spare cpu...
    It doesn't matter that the boards are lying on your desk...the psu should provide enough grounding,however,it might be worth a shot to connect an...
  12. Does plugging in a keyboard make any difference?...

    Does plugging in a keyboard make any difference?
    I'm prone to say that either a processor works or it doesn't. It sounds like something is shorting.
    Check if the backplate of your watercooler on...
  13. Can't hear anything but fan or pump noise. Please...

    Can't hear anything but fan or pump noise. Please answer questions asked above.
  14. Cool! I understand it totally, but i must say...

    Cool!
    I understand it totally, but i must say they improved the flaws it had.
    Anyways i just uninstalled it to see if EPU still works, and it does! Frequency and voltage are variable as it should....
  15. This is nice documentation, i really wondered how...

    This is nice documentation, i really wondered how it would be with air cooling. I hestitated when i built this system, but went for liquid anyway.
    By the way,the AIDA64 CPU stresstesting it way too...
  16. By doing a preliminary search i found that such a...

    By doing a preliminary search i found that such a R9 295x2 card can pull 700 Watts. (equaling 58,33 Ampères)
    Your single rail PSU can do 108 Ampères maximum. Assuming a real world value of 86,4...
  17. This post is golden really,saves you so much...

    This post is golden really,saves you so much heat!!! and yes,stable after 24h of IBT.
    So here a clean version ;-)
    Updated with stability improvement checks!
    This 'slow mode' button seems to have...
  18. Can you do some electrical measurements, and/or...

    Can you do some electrical measurements, and/or do you have any soldering skills?

    It sounds like the button on the rear that you use for Asus Flashback is internally hanging to the flash position....
  19. Especially speakers or headset through the front...

    Especially speakers or headset through the front port of your case? Not the back port?
  20. 2x8GB, 2400 Mhz. Kingston HyperX Savage,...

    2x8GB, 2400 Mhz. Kingston HyperX Savage, 11-13-14-32@1.65V.
    It did not matter if i had set the speed up to run slower, run on auto, with the manual timings that go with the speeds, or timings on...
  21. Just noticed that the 'slow mode' switch on the...

    Just noticed that the 'slow mode' switch on the board was set to 'on'... could this have been the culprit?
    Just turned it off, will see what happens!
  22. Replies
    2
    Views
    1,534

    I just bumped into a help topic from Asus that...

    I just bumped into a help topic from Asus that might apply to your power problem.
    They state that for a 1394 controller, the power management must be enabled.
    So in the device manager, check all...
  23. Hi Chris, i recently made the transition to Win...

    Hi Chris, i recently made the transition to Win 10. I wanted to rule out the 7 OS was failing somehow. But the symptoms remain exactly the same.
    Is there something critical that needs to be...
  24. Replies
    2
    Views
    1,534

    I have always had the same sensor behaviour. I...

    I have always had the same sensor behaviour. I remember in the AI suite,there's the possibility to monitor voltages with a live graph.
    You can actually see certain values in the graph bounce up and...
  25. CH5-FZ+FX9590 stability / have to disable core 7&8

    Hi all,

    I have been using this combination for a while now.
    And i remained pretty satisfied after the common startup problems that everyone encountered i guess.

    Until a few months ago...
Results 1 to 25 of 45
Page 1 of 2 1 2