Search:

Type: Posts; User: Zka17

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    305
    Views
    111,149

    Going to subscribe... :cool:

    Going to subscribe... :cool:
  2. Replies
    305
    Views
    111,149

    Agree... it does not have too much functional...

    Agree... it does not have too much functional benefit... - for HDDs a fan blowing on them is enough...
  3. Replies
    305
    Views
    111,149

    Regularly I'm using Gelid Extreme, but when I'm...

    Regularly I'm using Gelid Extreme, but when I'm running out of it then Arctic Silver MX-2 or MX-4...

    Haven't tried others yet, but among these 3 does not seems to be a difference...

    The point...
  4. Replies
    305
    Views
    111,149

    Cool beans, Profeus! :cool:

    Cool beans, Profeus! :cool:
  5. Replies
    305
    Views
    111,149

    There is absolutely no flow issue in parallel...

    There is absolutely no flow issue in parallel setups!

    The speed of the pump(s) is dependent on the rad's cooling capacity, which in turn depends on the rad surface, fans' speed and the ambient...
  6. Replies
    305
    Views
    111,149

    First of all, I'm not able to see that video as...

    First of all, I'm not able to see that video as it hits some copyright issues in US...

    Regarding the parallel vs serial loops on the graphics cards - the parallel is my choice... In serial loops...
  7. Replies
    305
    Views
    111,149

    I'm afraid that a Hailea chiller would prove an...

    I'm afraid that a Hailea chiller would prove an expensive mistake... specially a smaller one...

    I have my 500A cooling only the CPU, a 3970X pushed to 5.3GHz, and during benchmarks the chiller...
  8. Replies
    305
    Views
    111,149

    Sorry, Profeus for not answering earlier... got...

    Sorry, Profeus for not answering earlier... got busy with my work...

    Yes, basically I'm using a similar Dew Point calculator too!

    The Hailea 150A is pretty small, unfortunately... I have the...
  9. Replies
    305
    Views
    111,149

    Personally, I would go with the 900D from those...

    Personally, I would go with the 900D from those two... i think, it's more rad-friendly...

    If you have space around your system, an external rad setup could be even better - you can position it for...
  10. Replies
    305
    Views
    111,149

    A single D5 pump will be able to push the water...

    A single D5 pump will be able to push the water through that loop, but you may want to consider a second D5 pump with a dual serial top for them... that way you will have some redundancy too and...
  11. Replies
    305
    Views
    111,149

    Oh, I see it now! Don't worry about parallel...

    Oh, I see it now!

    Don't worry about parallel VGA blocks, if the pump can handle it (just get a decent pump), it will work fine! I've been running 4-way SLI/CF setups in the past with a single D5...
  12. Replies
    305
    Views
    111,149

    Not sure where the pump is in that setup... - the...

    Not sure where the pump is in that setup... - the only thing what matters really is to not run the pump dry at all, so your pump should be right after the res in the loop...
  13. Replies
    305
    Views
    111,149

    I'm always using "A" with the inlet on the GPU...

    I'm always using "A" with the inlet on the GPU side of the cards...
  14. Replies
    305
    Views
    111,149

    Yes, that is is often happening with...

    Yes, that is is often happening with air-cooling... waterblocks will most likely equalize the temps between the cards...
  15. Replies
    305
    Views
    111,149

    Not the water temp is important, but the core...

    Not the water temp is important, but the core temps of your CPU and GPU temps of the Matrix cards... - I would keep the CPU's cores below 75C at max load for 24/7 usage... the Matrix cards clocks...
  16. Replies
    305
    Views
    111,149

    Without proper equipment and experimental...

    Without proper equipment and experimental conditions you won't be able to calculate the exact amount of heat produced... so, practically you can rely only on other people's experience and your own...
  17. Replies
    305
    Views
    111,149

    The thing is that you have to find the equilibrum...

    The thing is that you have to find the equilibrum between the flow rate, radiator surface and fan settings on the radiator... it is different for every loop...

    A good thing with water-cooling the...
  18. Replies
    305
    Views
    111,149

    In a single loop, specially with higher flow...

    In a single loop, specially with higher flow rate, doesn't matter the order of the components... after a time the system gets balanced and you will have pretty much the same temps all over your...
  19. Replies
    305
    Views
    111,149

    Usually you have to calculate 2x120mm rads for...

    Usually you have to calculate 2x120mm rads for each block... I think, your system is a little bit low on rads... - but that's not meaning that it would not work, just your OC limits will be lower...
  20. Replies
    305
    Views
    111,149

    I can second that! Higher frequencies, specially...

    I can second that! Higher frequencies, specially with tight timings do require more voltages...
  21. Replies
    305
    Views
    111,149

    Shoot a PM to MarshallR... he is the best to ask...

    Shoot a PM to MarshallR... he is the best to ask about it...
  22. Replies
    305
    Views
    111,149

    When it's about to choose between EVGA an Asus,...

    When it's about to choose between EVGA an Asus, I'm would follow one thing... - air- or water-cooled? If you have limited founds, go with Asus Direct Cu-equiped cards for aircooling and choose EVGA's...
  23. Replies
    305
    Views
    111,149

    Actually, I have to correct myself... I'm using...

    Actually, I have to correct myself... I'm using mostly Asus cards... I do have 3x EVGA GTX480s, the Superclocked ones... :)
  24. Replies
    305
    Views
    111,149

    It doesn't really matter... it's about your...

    It doesn't really matter... it's about your preferences... mine is the PrecisionX and using Asus cards...
  25. Replies
    305
    Views
    111,149

    Well, you won't know until you won't try... :)...

    Well, you won't know until you won't try... :) Actually, OC'ing the graphics cards is somewhat easier than dealing with the CPU and memory settings in BIOS... (I know, there are applications for that...
Results 1 to 25 of 29
Page 1 of 2 1 2