Search:

Type: Posts; User: CharlieH

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds; generated 59141 minute(s) ago.

  1. To get your memory stable I suggest throwing some...

    To get your memory stable I suggest throwing some extra voltage to the VCCSA and VCCIO. When I am OCing (even though your not, you are technically OCing the memory as far as the CPU is concerned) to...
  2. Well if your running M.2 cards through PCH I...

    Well if your running M.2 cards through PCH I would worry more about their temps. They throttle when they get hot. They need heat sinks and good air flow in the case.
  3. Replies
    15
    Views
    1,842

    Once you set XMP on you can just change the clock...

    Once you set XMP on you can just change the clock speed to 2133 or 2400 whatever it defaulted to w/no changes in the BIOS originally. But your rated speed is 2666 which is what we were asking you to...
  4. Replies
    15
    Views
    1,842

    I concur with LiveOrDie you need to try your...

    I concur with LiveOrDie you need to try your memory at rated speeds. An easy way to do this and insure everything else is default is to either reset your CMOS from the MB via the reset button (I...
  5. Replies
    15
    Views
    1,842

    And back to the memory even if you don't OC/XMP....

    And back to the memory even if you don't OC/XMP. When I have memory issues and the defaults on it are set via XMP the three things I generally have to contend with to stabilize memory when I OC it...
  6. Replies
    15
    Views
    1,842

    May I start by saying what a very nice rig. I...

    May I start by saying what a very nice rig. I wanted that same 7980xe when I bought mine for the R6E but the BIOS was in it's early stages and it would not run correctly programs would just crash on...
  7. Replies
    6
    Views
    1,312

    I like the Intel Processor Diagnostic Tool 64bit....

    I like the Intel Processor Diagnostic Tool 64bit. I am not a fan of Prime95 its load is not very realistic and hard on the CPU. And Windows Memory Diagnostic to test my memory. I don't like the Intel...
  8. So I went to Intel's site to get the official...

    So I went to Intel's site to get the official version, same version ASUS is just now putting out, they put it out back in 6/4/2018:...
  9. The one they uploaded for the RE6 doesn't install...

    The one they uploaded for the RE6 doesn't install even though it says "Software installed" with a dialog and that's all it shows. I manually copied the files in and it uses the new version though....
  10. Replies
    5
    Views
    1,254

    The 90 day message is the kicker. In 90 days you...

    The 90 day message is the kicker. In 90 days you can no longer use the RAID array. To BigJohnny's point you cannot do this. You need to use Intel drives for the RAID not Samsung to get rid of the...
  11. Replies
    5
    Views
    1,254

    Pretty sure you have to use VROC with all the...

    Pretty sure you have to use VROC with all the drives you can't just use it on 2 of the 4. The bios setting for the hyper x16 is to split the x16 PCIE lane into 4 x4 lanes one for each PCIe NVMe SSD...
  12. Replies
    354
    Views
    63,095

    Also one last note if I remember correctly for...

    Also one last note if I remember correctly for GPUs x16 vs. x8 is negligible performance difference the GPU core and memory speeds matter way more. That is why 3xSLI 2 cards run x8 with no real...
  13. Replies
    354
    Views
    63,095

    So I looked in the Omega manual and saw this, so...

    So I looked in the Omega manual and saw this, so to get x16 on both cards you must have them in slot 1 & 2, slot 3 can only run at x8:
    79751
    Also this section of the manual explains where you set...
  14. Replies
    354
    Views
    63,095

    Well my 3rd slot ran x16 by default. Under...

    Well my 3rd slot ran x16 by default. Under advanced there is a list, I can't remember the name but under a sub menu I believe you can set the pcie speeds, I think normally by default they are auto....
  15. Replies
    354
    Views
    63,095

    As far as your Aquantia 10GB Nic goes 1) Make...

    As far as your Aquantia 10GB Nic goes
    1) Make Sure you have the latest Intel MEI Firmware installed
    2) Make sure you have the latest Intel MEI driver installed
    3) Install the latest Aquantia 10Gbs...
  16. Like I mentioned in my previous post I am running...

    Like I mentioned in my previous post I am running fine with an OC, XMP, VROC, etc. without seeing ANY issues here is my machine:
    (I mainly run VMs on this box everyday all day long usually for at...
  17. Replies
    354
    Views
    63,095

    I am trying to tell you, you do not have to...

    I am trying to tell you, you do not have to create the raid array in the bios. You can boot into windows and run the IRSTE software and the IAStorU which is in the tray, you double click it, then the...
  18. Replies
    354
    Views
    63,095

    Are you using the IRSTE driver/software and not...

    Are you using the IRSTE driver/software and not the IRST driver/software? It sounds to me like you may have installed the wrong one. The IRSTE has the VROC driver in it and can read the VMD...
  19. Replies
    354
    Views
    63,095

    To use VROC they gotta be intel drives, but the...

    To use VROC they gotta be intel drives, but the weird part is on the R6E you could RAID the samsungs (at least the 960 Pros) but you would get a expiration warning in the IRSTE GUI until you added...
  20. I am using it, I set extreme for the auto OC, it...

    I am using it, I set extreme for the auto OC, it set XMP and OCed like before, I use VROC for a data drive etc. I have been running it for about a week and haven't seen any issues so far. My chip is...
  21. Replies
    3
    Views
    2,412

    I am running 2.1.17. I had to go to the Device...

    I am running 2.1.17. I had to go to the Device Manager and access the 'Advanced' settings tab for the adapter and disable 'Recv Segment Coalescing (IPv4)'. My issue wasn't printing but it was adapter...
  22. I am not sure your config will work, but if it...

    I am not sure your config will work, but if it does you will be spanning contollers. And I know you cannot boot off spanned controllers, well at least it is not supported. So I don't think your...
  23. BTW the controllers worked this way for me, there...

    BTW the controllers worked this way for me, there are 3, Controller 0 1st HyperX16, Controller 1 2nd HyperX16, Controller2 DIMM Card (I have a single Samsung 960 Pro in that card)
  24. One note I use intel 900p SSDs, 8 of them. Not...

    One note I use intel 900p SSDs, 8 of them. Not sure about the samsungs working maybe with a VROC key?
  25. I run 2 HyperX16s both run at x16 with 4 divided...

    I run 2 HyperX16s both run at x16 with 4 divided x4 lanes. I had to put my GPU in a x8 slot to accomplish this.
Results 1 to 25 of 151
Page 1 of 7 1 2 3 4