Search:

Type: Posts; User: Arne Saknussemm

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds; generated 39957 minute(s) ago.

  1. Replies
    48
    Views
    1,771

    No almost about it...

    No almost about it...
  2. Replies
    7
    Views
    2,706

    I took the plunge and updated....it breaks a lot...

    I took the plunge and updated....it breaks a lot of things that were working fine.

    Really annoying! BETA software updates
  3. Replies
    164
    Views
    19,886

    Nice to know! I haven't taken the 1903 plunge...

    Nice to know! I haven't taken the 1903 plunge yet....
  4. Replies
    17
    Views
    1,056

    I don't run SLI anymore....maybe it's that;)

    I don't run SLI anymore....maybe it's that;)
  5. It's on Extreme tweaker tab... CPU Input...

    It's on Extreme tweaker tab...

    CPU Input Voltage
  6. LOL :D:D:D I overclocked a few percent more...

    LOL :D:D:D

    I overclocked a few percent more and they are back up to speed now for me :cool:
  7. Thanks...while I didn't find the post overly...

    Thanks...while I didn't find the post overly "useful means" I sure don't mind leaving you an upvote...
    80481
  8. "Never attribute to malice that which is...

    "Never attribute to malice that which is adequately explained by stupidity"
  9. You can run the XMP profile for the RAM without...

    You can run the XMP profile for the RAM without overclocking the CPU.

    XMP simply applies the rated timings/frequency/voltage for your RAM...the difference in heat between 2666 and the rated 3200...
  10. Well, it will depend on the ambient temp inside...

    Well, it will depend on the ambient temp inside your case I guess...

    I have an open test bench so temps are bound to be better....24 room temp and RAM is 3-5 degrees higher CPU at idle...2 degrees...
  11. Yes, correct. HWiNFO64 is the only monitoring...

    Yes, correct.

    HWiNFO64 is the only monitoring software I would recommend for this platform.

    Though, all software should have the offset already applied so, no, no need to add the 27...your idle...
  12. OK so it's a single kit which helps...it's not on...

    OK so it's a single kit which helps...it's not on the QVL but there is a similar kit that is...might be a question of tweaking...

    Try to raise DRAM voltage a bit Try 1.375 or 1.4v and set SOC...
  13. BIOS 0405 is the latest for ZEA (Latest for ZA is...

    BIOS 0405 is the latest for ZEA (Latest for ZA is 1701)

    3200 for 8x8 can be tricky for some processors and RAM combinations on this platform.

    What is the exact RAM part number? Is it a single...
  14. MCE is an overclock...it takes that one-core...

    MCE is an overclock...it takes that one-core turbo ratio and applies it to all cores.

    That error is usually a lack of Vcore...so maybe a slight bump in vcore is needed to run all core turbo ratio....
  15. https://www.youtube.com/watch?time_continue=1&v=ws...

    https://www.youtube.com/watch?time_continue=1&v=wsmHmYxyoxg
  16. I would be wary of no support for the SSD...

    I would be wary of no support for the SSD there...it might be fine but it might also be vibrating imperceptibly until it works loose or something like that...
  17. Replies
    10
    Views
    776

    RMA the CPU to Intel...if it's still under...

    RMA the CPU to Intel...if it's still under warranty....they are fast ...
  18. Replies
    3
    Views
    746

    I haven't seen anything like that except...

    I haven't seen anything like that except molecular acid...
  19. Replies
    13
    Views
    1,088

    I don't get that...should I complain...;)

    I don't get that...should I complain...;)
  20. Replies
    3
    Views
    273

    Well, it's like a green circle arrow...so I guess...

    Well, it's like a green circle arrow...so I guess it's meant to mean "reset"...or clear CMOS!:rolleyes:
  21. Replies
    3
    Views
    273

    Yes, Clear CMOS is best done with PSU power...

    Yes, Clear CMOS is best done with PSU power removed
  22. Replies
    3
    Views
    577

    Personally...I wouldn't do that...

    Personally...I wouldn't do that...
  23. Replies
    13
    Views
    1,088

    I updated OK... When I went to remove...

    I updated OK...

    When I went to remove "telemetry" as usual...there wasn't any! Hurray!

    No 3D options to untick...Hurray!
  24. Replies
    5
    Views
    759

    It's permanently free to try...for a limited...

    It's permanently free to try...for a limited period

    It appeared with a price in Uplay...but click on buy and the price gets discounted to zero at checkout
  25. There would be next to no point coming up with a...

    There would be next to no point coming up with a stress test/tuning utility that ran outside of an operating system. Stability has to cover the most used operating scenario for any PC. This is nearly...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4