Asus Z490 stuff

[RobertoSampaio]

Oh, no... I'm using #4 for a month...
Hope I didn't make a mess!
What it does for?
Going to AUTO...
What should I check to know if I fryed something?

[RobertoSampaio]

I Changed PLL Bandwidth from #4 to auto but the CPU PLLs OC do not changed... 2,32v. Is it normal?

[Falkentyne]

I Changed PLL Bandwidth from #4 to auto but the CPU PLLs OC do not changed... 2,32v. Is it normal?

Set it to "Default".
it should be 1.20v
2.3v can destroy the chip. This is a sub-zero setting.

[RobertoSampaio]

No matter if I select AUTO, Default, #1 or #4 in PLL Bandwidth... the HW-Info show CPU PLLs OC = 2,320V.

I tried load Defaults and its like HW-Info cant read this parameter and always show 2,320V, no more no Less.

I'm using HW-Info 64 v6.30-4240
Maximus XII formula bios 0707.


What can I do?

[martine-dee]

Do not touch that setting.

Is that about the CPU Load-line Calibration?

As far as I know, it is supposed to flatten the voltage variation, at the expense of the power used. The higher the value, the less voltage variation there will be. I like it, because I have the voltage manually set. For me, this is on the Level 8.

A noob question though, the recommended voltage to start from, is that 1.35 V or 1.035 V? I've tried the low voltages, such as 1 volt or under; Windows load-up will crash the box on that. It's at 1.35 V for me, and even at the Level 8 LLC there are some voltage variations.

[RobertoSampaio]

I think PLL Bandwidth is a kind of filtering (Phase-locked loops).
This setting alters the CPU PLL's Oscillator voltage.

https://www.intel.com/content/dam/ww...m10_clkpll.pdf

The problem I have is that the WH-info read actual=2,32v; Minimum=2,32v; max=2,32v... No matter which PLL Bandwidth # I use..

Its like it is frozen...

It shall be about 1,2v...

[Falkentyne]

No matter if I select AUTO, Default, #1 or #4 in PLL Bandwidth... the HW-Info show CPU PLLs OC = 2,320V.

I tried load Defaults and its like HW-Info cant read this parameter and always show 2,320V, no more no Less.

I'm using HW-Info 64 v6.30-4240
Maximus XII formula bios 0707.


What can I do?

Power off

Unplug the power supply cable or turn off the PSU switch.

Short the clear cmos jumper for 30 seconds, with another spare onboard jumper (e.g. Ln2 jumper), or a screwdriver, or press the clear CMOS button for 30 seconds.

Release/remove, then reapply power.

[RobertoSampaio]

All right !
Now CPU PLLs OC=1,200V !!
Thanks a lot !

[RobertoSampaio]

Hi folks,

I have a Maximus XII formula and I have some issues with OLED and armoury crate...
When I set what to display in OLED in armoury crate and reset the PC the OLED loose the configuration...

Is it an armoury crate issue ? Is there a way to set the configuration without armoury crate?

Asus could implement this configurations in BIOS!

[taco99]

I think that is part of the changes they made to livedash control over all. All OLED products including Ryujin do this now. It's supposed to help with display burning which my Ryujin 360 has really bad already. I just applied the updates via Armory Crate and it started flickering too every like 3 seconds. It's the new normal.

I have the oled flicker too after the bios update. What do we do?