Page 2 of 4 FirstFirst 1 2 3 4 LastLast
Results 11 to 20 of 35
  1. #11
    ROG Member Array
    Join Date
    May 2021
    Reputation
    10
    Posts
    8

    Quote Originally Posted by Silent Scone@ROG View Post
    Sounds like the system isn't stable enough to pass a cold boot every time. Try increasing VSOC voltage. 3600 should scale to around 1.08v automatically depending on board and UEFI revision. You can try up to 1.15v and see if this resolves the problem.




    Operating system stability and POST stability are intrinsically related but not one and the same. POST stress tests are designed to test integrity in a way that looks for signals encroaching on one another. If the system was able to POST on an unsuccessful POST stress test, the system would be unstable
    I have checked my ram are stable on 3600 Mhz also I have test on Memtest and there was 0 error.

  2. #12
    ROG Member Array
    Join Date
    May 2021
    Reputation
    10
    Posts
    8

    Quote Originally Posted by rafaynaeem View Post
    These are the spec of my computer
    Spec:
    Ryzen 7 5800x
    Asus Rog Strix b550-E (Bios Version 2201 beta)
    G. Skill Trident Z RGB 16GB 8x2 DDR4 3600MHz F4-3600C18D-16GTZRX
    MSI A850GF
    I'm facing this issue on my ASUS B550-E gaming when I enable D.O.C.P and put my rams to 3600 MHz everything work fine my system boot up normally it doesn't matter how many time I restart my system it boot up normally but when I unplug my PSU and then turn on my pc it show DRAM light and don't show any display unless I clear CMOS or cold start my system.
    And yes when I set to 3466 MHz every thing work fine even when I unplug my PSU and again plug it back everything work fine but still I want to use my rams to their full potential like at 3600mhz.
    Does any one find the solution for this issue?
    I finally found the solution but the downside is I have increase the Cas latency of my ram.
    My Pc specs:
    ryzen 7 5800x
    asus rog strix B550-E
    f4-3600C18-8GTZRX
    the timing of rams were 18-22-22-42
    the issue I was facing was when I unable d.o.c.p and set my rams to 3600 Mhz every thing worked fine my rams were stable but when I shutdown my pc and unplug my psu and than start my system it stuck on cold boot and show 1F error or some times show 0d error than I have to push the power button for 3 seconds so my pc shutdown than on 2nd go it bootup normally I use every method like setting dram timings manually and even use dram calculator but still facing this issue but than I just increase cas latency 18 to 20 and TRC 86 to 90 after doing this my system boot up and now I don't face cold boot issue.

  3. #13
    ROG Member Array
    Join Date
    Jan 2021
    Reputation
    10
    Posts
    23


  4. #14
    ROG Enthusiast Array
    Join Date
    Jul 2013
    Reputation
    33
    Posts
    50

    You can also try to lower your ram frequency + timings.

    for 3600@18-22-22-42, you can try 3200@16-20-20-40

  5. #15
    ROG Member Array
    Join Date
    Jan 2021
    Reputation
    10
    Posts
    11

    Unhappy B550-E cold boot failure when XMP is on. Q-codes are 0d or IF

    I have the same problem with XMP profile - cold boot after disconnecting from electricity. If disconnected for 1-3 hours, it sometimes starts normally. If disconnected overnight - will not start and Q-codes are 0d or IF.
    If XMP is disable - there is no problems with cold boot after disconnecting from electricity.
    Technical support can not explain what the problem is (mayby CPUs memory controler).
    MemTest - no errors AIDA - no errors. No CPU overclocking. The system is stable. I can even set DRAM to 3600Mhz 16-15-15 without any problems.

    Has anyone found a cause or solution yet?



    For reference my system components are as follows:
    CPU: 5600x
    CPU Cooler: Arctic Liquid Freezer II
    RAM: Corsair / CMW16GX4M2C3200C16 ver 4.31 (Samsung B-die), from QVL
    GPU: Asus RX470-4G-gaming
    Mobo: Asus Rog Strix B550-E
    BIOS: 2006
    OS Disk: Corsair MP510 480MB
    PSU: Seasonic Focus PX-550 Platinum

  6. #16
    ROG Member Array
    Join Date
    Jan 2021
    Reputation
    10
    Posts
    11

    B550-E cold boot failure when XMP is on.

    In my case the new bios 2403 (not 2604) has solved the problem. Before that only timings 19-22-22 at 3600mhz did not cause the cold boot issue.
    Last edited by forin; 06-24-2021 at 07:55 PM. Reason: bios 2403 (not 2604)

  7. #17
    Administrator Array Silent Scone@ROG's Avatar
    Join Date
    Mar 2016
    Reputation
    178
    Posts
    2,342

    Quote Originally Posted by rafaynaeem View Post
    I finally found the solution but the downside is I have increase the Cas latency of my ram.
    My Pc specs:
    ryzen 7 5800x
    asus rog strix B550-E
    f4-3600C18-8GTZRX
    the timing of rams were 18-22-22-42
    the issue I was facing was when I unable d.o.c.p and set my rams to 3600 Mhz every thing worked fine my rams were stable but when I shutdown my pc and unplug my psu and than start my system it stuck on cold boot and show 1F error or some times show 0d error than I have to push the power button for 3 seconds so my pc shutdown than on 2nd go it bootup normally I use every method like setting dram timings manually and even use dram calculator but still facing this issue but than I just increase cas latency 18 to 20 and TRC 86 to 90 after doing this my system boot up and now I don't face cold boot issue.

    The memory wasn't stable enough to pass training. 0d is a training error, you can try increasing VDIMM if wanting to dial back latency

  8. #18
    ROG Guru: Brown Belt Array RedSector73 PC Specs
    RedSector73 PC Specs
    Laptop (Model)FA506IU-AL130T x 2
    MotherboardROG CROSSHAIR VIII HERO (WI-FI)
    ProcessorAMD Ryzen 9 3900X 12-Core Processor
    Memory (part number)4 x G.SKILL F4-3800C14D-16GTZN 14-16-16-36 Samsung B-Die
    Graphics Card #1Gigabyte Aorus RTX 2080 Ti Xtreme WaterForce (GV-N208TAORUSX W-11GC)
    Sound CardArctis DAC
    MonitorAsus ROG Swift PG348Q
    Storage #1ADATA SX8200PNP 1TB
    Storage #22 x Samsung SSD 840 EVO 250GB
    CPU CoolerCoolermaster Liquid Pro Master 360
    CaseEVGA DG-87 Gunmetal Grey Gaming Case
    Power SupplyEVGA SuperNOVA G2 750W Gold Power
    Keyboard Corsair K95 RGB Platinum
    Mouse Corsair Gaming Sabre RGB Gaming Mouse
    Headset ARCTIS Pro Wireless
    Mouse Pad Cooler Master MP750 RGB Cloth Gaming Mouse Pad Extra Large
    OS Windows 11 64bit Pro
    Network RouterPfSence Intel i5-10210U 6 Port
    Accessory #1 TP-Link Gigabit 8&6 Port Switches

    Join Date
    Apr 2018
    Reputation
    65
    Posts
    1,258

    Quote Originally Posted by Silent Scone@ROG View Post
    0d is a training error
    This is fav. error at least I'm getting close when this shows up !

  9. #19
    Administrator Array Silent Scone@ROG's Avatar
    Join Date
    Mar 2016
    Reputation
    178
    Posts
    2,342

    Quote Originally Posted by RedSector73 View Post
    This is fav. error at least I'm getting close when this shows up !
    It's great when it shows up after a few weeks, too

  10. #20
    ROG Member Array
    Join Date
    Apr 2021
    Reputation
    10
    Posts
    15

    Boot problem

    I have that trouble, but if I activate the ErP (S4 + S5) option to turn off all USB and lights, when I turn on the PC it can't boot and I need to reboot until it decides to boot. What should I do ?

    CPU: RYZEN 5 5600X
    VIDEO: ZOTAC RTX 3080 Trinity OC
    MOTHER: ASUS ROG STRIX B550-E GAMING
    RAM: F4-3200C16D-32GTZR
    NVME/SSD M.2: WDS100T3XHC-00SJG0 / GP-AG4500G
    CPU COOLER: NOCTUA NH-U12S-Chromax Black
    FUENTE: NZXT C850
    COOLERS: DEEPCOOL ARGB x6
    MONITOR: TUF GAMING VG27A (2560px1440p)
    BIOS: 2003

Page 2 of 4 FirstFirst 1 2 3 4 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •