Page 31 of 31 FirstFirst ... 21 29 30 31
Results 301 to 304 of 304
  1. #301
    ROG Guru: Orange Belt Array
    Join Date
    Sep 2013
    Reputation
    30
    Posts
    268

    Cheers Niko

    I was doing all above except deleting the temp files.

    Is there a way to isolate which is to blame?

    Also would too tight timings on the ram cause this?

  2. #302
    ROG Guru: Brown Belt Array nikosa43's Avatar
    Join Date
    Jun 2012
    Reputation
    73
    Posts
    1,014

    To isolate would be for ...research . I am not that patient . I just delete them and it works. Tight timmings can easily corrupt files because you push it to its working limits and everything is loaded there. For having the less bad surprises use SuperPi. After setting your RAM through BIOS, before you run RB, run SuperPi 4M or 8M. If you pass without any error you have a very good indication for stability. These tests are very demanding and if you over did it they will fail. 32M is the most intense but takes ages and I can't wait that much

  3. #303
    ROG Guru: Orange Belt Array
    Join Date
    Sep 2013
    Reputation
    30
    Posts
    268

    Quote Originally Posted by HiVizMan View Post
    So close to 600 Poco nice work.
    Cheers HiViz

    Getting those extra 5 points on this system may be a lot harder than getting the 101 increase over stock without adding sufficient cpu coling. Either my ram is at its limit, or worse my IMC has peaked. I have read that the IMC on this cpu is is rated @ 2133mhz and that the Dom Plats below this speed have little head room. I could not get these to run @ 2133 with a 200 fsb, despite going to 1.75v and upping some other relevant voltages. But I got it to run @ 2134 with a 225 fsb @ 1.71 volts with what I thought were impressive timings for this speed. Anything higher just does not seem to stabilize, even when increasing the volts to the IMC. I expected I may need to get faster ram to get more out of the fsb or to rule out what is the bottle neck. Given the 9370 that leads has a lot higher fsb than I can achieve with this ram I am hoping that is what has peaked.
    Opinions you or others may have are welcomed, even if it is to confirm or dismiss my logic.
    Last edited by Poco OM; 11-19-2013 at 06:07 PM.

  4. #304
    ROG Guru: Yellow Belt Array
    Join Date
    Mar 2012
    Reputation
    10
    Posts
    244

    Well, I think I might get back into action with this. Is everyone moving to V2 beta, or still using 1.1 until final release of V2?

    Have a couple questions.

    I have been doing some benching with a S1156 i5-760. Using the same Dominator Platinum 2400mhz ram from my X79 system (yes, it runs dual or quad), I can clock it to 2400mhz not problem even though the mobo (Sabertooth 55i) only 'officially' supports up to 2000mhz. Problem is, at 2400mhz, RealBench crashes. I beleive it is due to IMC voltage.
    My question is, what have people found to be an upper limit on S1156 IMC voltage? I have had it as high as 1.39v, but worried I might cook the CPU. Also, I have had the Vcore as high as 1.45v. Anyone know how much higher I can go?

    Also, so far I have clocked the CPU as high at 4700mhz. What is an average high overclock on this CPU. As an example of average, can it be clocked as easily to 5.0GHZ as an X79 CPU can? 5.0GHZ is a common overclock and easily obtained on an X79 system.


    And WOW! Man do I have some work to do! 900 score in RealBench? I gonna have to tuck the 'roids in to get close to that. LOL

    EDIT:
    Sorry, I should say the Dominator clocks to 2375mhz no prob with IMC at 1.3v. Any bclk higher and no post. This is were it max's out on my X79 system.
    It seems this memory kit max's out in frequency around same speed whether it is in an X79 or 55i system. Or could 2375mhz be the max speed for 55i, and 2375 is all the IMC on my 3930K can do? Asus does state 2000mhz max supported for Sabertooth 55i.
    Last edited by xmanrigger; 12-02-2013 at 09:22 PM.
    GUTS: Rampage IV Formula (4004) / Intel 3930K / 16GB Dominator Platinum 2400mhz / Corsair NeutronGT 240GB SSD / 2X EVGA GTX680 4GB 2-Way SLI / Corsair AX1200i PSU / Genesis 9000B Case

    WATER: Watercool HeatKiller REV3.0 - CPU / 2X Watercool HeatKiller GPU-X3 - GPUs / 1X XSPC RX240 rad / 1X EK Coolstream 480 rad / XSPC Dual Rez / MCP355 Pumps / DISTILLED WATER + Silver Coil

Page 31 of 31 FirstFirst ... 21 29 30 31

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •