Hi!!
I have been all weekend giving BnB mod. Not change the end panels . The main reason for the change was that it did not overlap the distance between fans and therefore the holes. But I happened to catch the file and make the hole a tad longer , instead they were circular. And the result has been good , with consequent savings !
I roll over and I show as I have the project. Before doing anything I preferred to present / assemble everything and so go looking possibilities and if prompted follow the script that had established . I 'll go commenting ...
This place still no where lol, something so small. Surely nearly of aquaero or pumps..
The switches and USB 3.0 are not placed poruqe sleeve that I have that make me still some left. Besides not know if this will put LD Cooling panel or the Switch 810 that I have saved . A part of the conetores USB 3 carries audio , rear leds switch and card reader ...
A large box for one or two radiators , but if you stick another be carefull.. Scares me when I have to put the tube down the little space you have to stop putting a finger ...
Reservoir with extras . Led warning aqueaero temperatures , over pressure safety valve ( not liquid spits as many believe. These air that is expelled due to overpressure . If the valve is near the liquid or within the circuit if ejected. But is placed in the top of the tank ( not sharing circulation ) at fill and ready ...
A filter for impurities that may arise ( plastic chips / acetal , copper , paint, ... ) with 1 valve on each side to open the circuit to the minimum leakage and rotary fittings to unscrew . To this I have to make a good support. These are a few props rotating (elbows , 45, rotating , ...) and is fixed ...
To detail the back of Aquaero and block cooling option ...
The front 140x2 rad , runs push-pull configuration but I detected a fault in the box. It turns out that if you put filters the input, for limparlos have to get everything , heated either the front or the top with fans . Is everything subject to the external grid . So I will fabricarme supports that caught the inside and is rad who hold this if you remove the grille. I'm in the process ...
The bottom of the tank , pumps mounted in series and the sensor. Under the HDDs that are bugging me , then I tell ...
The pumps and top with more detail. I have to turn the pump so that the cables go forward.
Well, HDDs ... I tell you , I put the radiator with the jacks down, why? Well because the route is so minor, to have bombs at the bottom should go up and then down to the graphics . Then , when emptying / drainage strip all the liquid . Besides , right now I have no place to put a valve and fillport desgüe . Fillport only if, but I love him because having closed valve , tube fitting place it , open the tap and the liquid is going where you want ...
In the following pictures you will see that there is little , or rather no space , salts with elbow 90 or you eat boogers , and there ventis missing interior ...
The solution that had , and still think how to do it without touching the box ( trim, not shoddy power , and had the switch for it,
🙂 ) is to raise the box HDDs keeping silent blocks . They won it in the bottom space and not have to do so much jog , climb down as I do now also , as I said before, a drain in the lowest point of the circuit.
Now on to the back ...
The invention that I have assembled to place the deposit which suits me for the RL . Scraps of laser grid that held before ( switch) the same tank ... The white is the protective plastic .
And that's it , I still lack a lot, but I think I have much more advanced and where to go to fixed shot . I have to buy more accessories, not many , some elbows , filter (I've broken paws ) , extension and 3-way valve , painted fans, no no, not going to be so , surely some I had already asked / imagined. And Screws . If , at the end just a home hardware . Consequently they are of M4 rads . The box of luck and joy , is M3 and above uses the same screws you buy, semi - round head allen ...
Nothing guys hope you liked it !
Raijintek Ophion EVO | Asus ROG Strix X470-I Gaming | AMD Ryzen 7 2700X | Ballistix Tactical Tracer RGB 16GB DDR4-3000 (x2) 32GB | KFA2 GeForce® RTX 2080 OC | M.2 Samsung 950 PRO 500GB | SSD Samsung 750GB | HDD WD Green 3TB | Corsair SF600 | Logitech G710+ | Logitech G502 Proteus Spectrum | Corsair H100i RGB Platinum | Corsair ML120PRO | W10 Pro