Results 1 to 1 of 1
  1. #1
    Forum Moderator Array ROG.PH's Avatar
    Join Date
    Mar 2016

    Upgrade 101: GL552

    Click image for larger version. 

Name:	GL552 Upgrade 1200 x 600 template.png 
Views:	1 
Size:	407.3 KB 
ID:	57083

    While the world is wanting thinner and lighter laptops, it's easy to forget that for a laptop not much larger in size you can usually get the same great specs or better for less money. Not only that, there are generally more ports, no need for external optical drives, the ability to play games or do 3D rendering, best of all - you have room for upgrades! Let's take a look at the ROG GL552 which can be configured with up to a Core i7 processor, 16GB of DDR3L memory, and Nvidia GeForce GTX 950M graphics. Let's see what you are able to upgrade. First, simply unscrew the two screws at the top of the back panel. Lift it up 45° (do not lift it up past 90°) and slide it out upwards.

    Click image for larger version. 

Name:	1.jpg 
Views:	3 
Size:	63.6 KB 
ID:	57077

    After removing the back cover, you will see three compartments where you may be able to upgrade (depending on what you already have). You are able to fill up the two slots for memory (up to 16GB), an M.2 slot for PCIe SSDs (best for installing the OS onto), and a 2.5" hard drive bay for even more (HDD) or faster (SSD) storage.

    Click image for larger version. 

Name:	2.jpg 
Views:	2 
Size:	71.6 KB 
ID:	57078

    Up to two 8GB sticks of DDR3L (it's important to know L denotes Low-Voltage in case you somehow manage to find sticks of DDR3, which will not work since they are not dual voltage capable) SO-DIMM memory for a total of 16GB. Below you can see two free slots, one is stacked on top of the other so make sure you install the bottom module first. Align the pins to make sure you have the module the right way up, insert the memory into the slot angled at about 30°, use your thumbs and press evenly on both sides to make sure the module goes all the way into the slot, finally, push the top of the module down towards the motherboard until both of the locks on the sides click into place. Repeat the process for the other module.

    Click image for larger version. 

Name:	3.jpg 
Views:	1 
Size:	94.1 KB 
ID:	57079

    It's highly recommended to install your OS in the M.2 SSD (even if you already have a SATA III SSD in the 2.5" bay) if you like speed. Installation is as easy as unscrewing the little screw (see below), inserting the M.2 SSD into the slot and pressing down towards the motherboard, and then securing that screw again.

    Click image for larger version. 

Name:	4.jpg 
Views:	1 
Size:	90.2 KB 
ID:	57080

    Next to the M.2 bay is the 2.5" hard drive bay, there are four screws (shown in red) you need to remove first.

    Click image for larger version. 

Name:	5.jpg 
Views:	0 
Size:	92.3 KB 
ID:	57081

    After removing the screws, slide the bracket to the left (as in the picture below), replace the hard drive with a new one by removing the screws on the bracket. Make sure to purchase a new drive with a SATA III interface (not that you can find an IDE one nowadays, but get SATA III supporting 6Gb/s for best performance), also make sure to put the new drive in the bracket the right way and screw it back in.

    Click image for larger version. 

Name:	6.jpg 
Views:	1 
Size:	315.3 KB 
ID:	57082

    Replace the back cover and voila! A new computer! Almost.

    Last edited by ROG.PH; 04-26-2016 at 06:54 AM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts