Page 1 of 5 1 2 3 ... LastLast
Results 1 to 10 of 49
  1. #1
    New ROGer Array InStY PC Specs
    InStY PC Specs
    MotherboardAsus ROG Zenith Extreme X399
    ProcessorAMD Ryzen Threadripper 1950x
    Graphics Card #1EVGA Geforce GTX Titan X
    Storage #1Samsung EVO 850 500gb SSD
    Storage #2HyperX 240gb SSD
    CPU CoolerHome Made with pipes and duct tape
    CaseNZXT H440 Razer Edition
    Power SupplyEVGA Supernova 800 G2 800w
    Keyboard Logitech G910
    Mouse Razer Deathadder 2013
    Headset Asus Strix 7.1
    Mouse Pad Razer Goliathus Control
    OS Windows 7 Home Premium 64 bit
    Accessory #1 HTC Vive

    Join Date
    Sep 2017
    Reputation
    10
    Posts
    2

    ROG Zenith Extreme wont power up.. Help?

    So im new to building computer. Weell almost new to it. I've builded some before but been lucky enough to not have any big problems except the one i have now.

    Just got done installing the motherboard and stuff (Specs at the bottom) and for some reason i cant start my computer.
    When i first plugged in the power cable and switched on the power button on my psu, the RGB lights on the motherboard turned on (dont know if its supposed to do that).
    And the Front power button on my case and the Start button on the motherboard didnt work either (worked on my old components).
    Checked the wires for the front power button and everything is correctly connected.

    I also started up the psu with the 24pin tool to see if there was any problem with the psu but everything that was connected got power.
    The two cpu 8pins was connected to the motherboard when i tested the psu and the rgb lights on the motherboard turned on.
    Connected a speaker to the motherboard to see if it was any problems but i cant even get the motherboard to start the rest of the components so no beeping there.
    I think its the psu or something that causes the problem but im not an expert so please try to stop me before i buy me a new expensive one.
    NEW: after some reading about psu i dont think the problem is the psu... now im lost.

    What can be the problem?
    If you guys know something then please share.

    My specs: (also the specs i used first time i powered it up)
    AMD Ryzen Threadripper 1950x
    Asus ROG Zenith Extreme X399
    EVGA Geforce GTX Titan X
    Corsair Vengeance RGB 16gb*2 3000MHz
    EVGA Supernova 850 G2 850w
    HyperX 240gb SSD





    Last edited by InStY; 09-20-2017 at 04:51 PM.

  2. #2
    ROG Enthusiast Array
    Join Date
    Sep 2017
    Reputation
    10
    Posts
    45

    The lights on the motherboard flashing are normal (you can turn that off in the bios)

    A few questions:

    1) Did you try to turn the MB on from the on/off switch attached to the board? If it does turn on then you might have got the pin connection backwards on your quick connectors
    2) Did you check to see if the 24 pin and two 8 pins are seated properly (I had an issue on one build that all the lights on my rig flashed on/off and he fans turned half a spin, my 24 pin connector was not seated properly

  3. #3
    New ROGer Array IvoSilva PC Specs
    IvoSilva PC Specs
    MotherboardAsus ROG Zenith Extreme
    ProcessorAMD Ryzen Threadripper 1950X Hexadeca-Core
    Memory (part number)G.SKILL F4-3200C14Q-32GTZ (4x8GB)
    Graphics Card #1SAPPHIRE Radeon™ RX Vega64 8G HBM2 Limited Edition
    Storage #1Samsung 960 PRO NVMe M.2 1TB
    CPU CoolerNZXT Kraken x62
    CaseThermaltake View 31 TG RGB
    Power SupplySeasonic Prime Gold 1000W 80+ Gold
    Keyboard Logitech G910 Orion RGB Spectrum Mechanical Gaming Keyboard
    Mouse Logitech G502
    Headset Sennheiser HD650
    OS Windows 10 Professional x64

    Join Date
    Sep 2017
    Reputation
    10
    Posts
    25

    You should also try with different memory setups, meaning, if you have more than 2 dimms, like 4 or 8, try with less, even a single dimm in the appropriate socket. Check the manual for the proper dimm positioning, since you do have to have the dimms in different slots according to your particular memory setup.

    If you have PCI-e cards other than de graphics card, also try removing them from the build and leaving it bare minimum and then add one by one.

  4. #4
    ROG Guru: Yellow Belt Array
    Join Date
    Nov 2014
    Reputation
    10
    Posts
    140

    Did you tighten all 3 screws in the CPU load plate properly?
    I would look at it again too,the TR4 socket is huge and all 4094 pins need proper contact to CPU
    and that require quite some pressure from the load plate.
    No need to over-tighten them, just make sure they are all in until it stops like normal.

  5. #5
    ROG Guru: Black Belt Array Korth PC Specs
    Korth PC Specs
    MotherboardASUS X99 R5E (BIOS2101/1902)
    ProcessorHaswell-EP E5-1680-3 SR20H/R2 (4.4GHz)
    Memory (part number)Vengeance LPX 4x8GB SS DDR4-3000 (CMK32GX4M4C3000C15)
    Graphics Card #1NVIDIA Quadro GP100GL/16GB, 16xPCIe3, NVLink1 (SLI-HB)
    Graphics Card #2NVIDIA Quadro GP100GL/16GB, 16xPCIe3, NVLink1 (SLI-HB)
    Sound CardJDS Labs O2+ODAC (RevB), USB2 UAC1
    MonitorASUS PG278Q
    Storage #1Samsung 850 PRO 512GB SSDs, 4xSATA3 RAID0
    Storage #2Comay BladeDrive E28 3200GB SSD, 8xPCIe2
    CPU CoolerRaijintek NEMESIS/TISIS, AS5, 2xNH-A14
    CaseObsidian 750D (original), 6xNH-A14
    Power SupplyZalman/FSP ZM1250 Platinum
    Headset Pilot P51 PTT *modded*
    OS Arch, Gentoo, Win7x64, Win10x64
    Network RouterActiontec T3200M VDSL2 Gateway
    Accessory #1 TP-Link AC1900 Archer T9E, 1xPCIe
    Accessory #2 ASUS/Infineon SLB9635 TPM (TT1.2/FW3.19)
    Accessory #3 ASUS OC Panel I (FW0501)
    Korth's Avatar
    Join Date
    Mar 2015
    Reputation
    152
    Posts
    2,719

    ASUS/ROG X399 Zenith Extreme motherboard manual.

    Reversed wires on the POWER switch won't affect anything, it's just a momentary-contact push button, no diodes, it'll work when wired "backwards". But a miswired or reversed Q-Connector block would be bad, the POWER switch must be properly wired up (RESET switch and LEDs should also be properly connected but they aren't strictly necessary to test boot the system). The Q-Connector block is only a convenience, so you don't have to figure out where all the wires go or reach into awkwardly tiny spaces every time you unplug the board, but it doesn't have to be used and the POWER switch contacts can be plugged directly to the motherboard pins when testing/troubleshooting.

    Test if the chassis POWER (and RESET) switches work with a DMM, if you can. Or even use a different (external) switch if necessary. Quickly confirming/denying that it's a bad switch or bad switch wire(s) can save you from hours of frustrated troubleshooting effort, lol, I've wasted time trying to troubleshoot faults on motherboard while assuming a high-quality chassis had high-quality electrical before (and, it turns out, sometimes the chassis electrical is cheap and shoddy, lol).

    Are any of the four Q-LEDs (near the memory slots) lit up when you power the system ON? If so, they're indicating common critical hardware faults: CPU (red), DRAM (green), VGA (white), BOOT (yellow).

    The CPU_READY LED (between CPU socket and adjacent PCIe slot) should be lit green if CPU is ready to boot. If it's unlit or lit red there's a problem. I'm guessing this is the advanced new version of the traditional old green LED which indicated motherboard is receiving (standby) power.

    The HD_LED (near the SATA ports) indicates hard drive activity. Unlit when no drive connected or drive is inactive. I'm unsure if it works with SSDs, lol.

    Strip the system down to essential hardware - PSU, motherboard, CPU (and CPU cooler, with TIM grease/paste between them!), fans/pump (if needed for CPU cooling), RAM (in slots DIMM_A1 and DIMM_C1), GPU card (in slot PCIEX16_1), boot drive (in SATA6G_1), keyboard and mouse (in Rear I/O USB ports, preferably keyboard in "U31G1_1" and mouse in "U31G1_2", the upper/lower couple of "black" USB3 ports slightly to the right of center) - remove all other hardware (unplug audio, unplug front panel connectors, remove all other drives and USB devices, network hardware, TPM module, ROG_EXT device, etc) until you know the important stuff all works. Overkill but methodical, and it only takes moments.

    Ensure the "RSVD" switch if OFF, the "PCIEX16_SW" switch is ON for slot 1 (ON/OFF shouldn't matter for slots 2/3/4 when unpopulated), the "LN2_MODE" jumper is disabled (bridging pins 1 and 2, not 3). 24-pin EATXPWR and both 8-pin EATX12V from PSU must be plugged into motherboard (and 6-pin and 8-pin PCIE12V from PSU must be plugged into your Titan X) or it won't boot. Ensure the DDR4 DIMMs and GPU card are firmly seated.

    I assume your CPU (and CPU cooler) is properly installed. Hopefully no bent pins or uneven mounting or whatever.
    "All opinions are not equal. Some are a very great deal more robust, sophisticated and well supported in logic and argument than others." - Douglas Adams

    [/Korth]

  6. #6
    New ROGer Array
    Join Date
    Sep 2017
    Reputation
    10
    Posts
    9

    Quote Originally Posted by InStY View Post
    So im new to building computer. Weell almost new to it. I've builded some before but been lucky enough to not have any big problems except the one i have now.

    Just got done installing the motherboard and stuff (Specs at the bottom) and for some reason i cant start my computer.
    When i first plugged in the power cable and switched on the power button on my psu, the RGB lights on the motherboard turned on (dont know if its supposed to do that).
    And the Front power button on my case and the Start button on the motherboard didnt work either (worked on my old components).
    Checked the wires for the front power button and everything is correctly connected.

    I also started up the psu with the 24pin tool to see if there was any problem with the psu but everything that was connected got power.
    The two cpu 8pins was connected to the motherboard when i tested the psu and the rgb lights on the motherboard turned on.
    Connected a speaker to the motherboard to see if it was any problems but i cant even get the motherboard to start the rest of the components so no beeping there.
    I think its the psu or something that causes the problem but im not an expert so please try to stop me before i buy me a new expensive one.
    NEW: after some reading about psu i dont think the problem is the psu... now im lost.

    What can be the problem?
    If you guys know something then please share.

    My specs: (also the specs i used first time i powered it up)
    AMD Ryzen Threadripper 1950x
    Asus ROG Zenith Extreme X399
    EVGA Geforce GTX Titan X
    Corsair Vengeance RGB 16gb*2 3000MHz
    EVGA Supernova 850 G2 850w
    HyperX 240gb SSD





    If you have a pci-e power supply going in to the second motherboard plug it won't boot. You can run just one power supply line to the motherboard and it will boot.

  7. #7
    ROG Enthusiast Array
    Join Date
    Mar 2013
    Reputation
    10
    Posts
    32

    Remove all add in cards (Video, etc), remove the memory, and disconnect everything from the motherboard except the for power. Your system should just have the motherboard (with internal speaker attached), CPU, and power supply. Turn on the computer now. If everything is OK, it should power on and give you a beep code. If it still doesnt power on, then check to make sure the 24 pin and 8 pin CPU power connectors are fully seated to the motherboard. If everything is connected and you still get no beeps, you most likely have to re-seat the CPU. Threadripper CPUs install different than every other type of CPU out there. Here is a video of the process:

    https://www.youtube.com/watch?v=RUOZE0N5WE8

    The guy is kinda ghetto, but he also destroys stuff by not installing things correctly, so he points things out from personal experience so other can learn from his mistakes. Make sure you follow everything he does in the video....

    While you have the CPU out, take a look at the socket on the motherboard to make sure nothing got bent from your previous installation. If it looks OK, re-install the CPU per the video's instructions and try the initial scenario again (motherboard with speaker, power, and CPU installed- then turn on and listen for beep codes). If you still dont get beeps, then you either have a bad motherboard or CPU. You "could" have a bad power supply but that is highly, highly unlikely.

  8. #8
    New ROGer Array
    Join Date
    Sep 2017
    Reputation
    10
    Posts
    6

    Exclamation

    100% your ram is wrong , not quad channel



    important = 2 single channel ram NOT dual ,,,, 4*dual channel ram NOT quad so you must use real 4 quad channel ram(4 ram in 1 box writen quadchannel on it ) , not 4* dual channell*
    (in ryzen cpu you must use only 2*dual channel , never never use 1*single channel ram , your system cant start , even start will give you tiny freeze
    on threadripper you cant use 4* dual channel or 4*single channel ram !!!!
    example true ram for threadripper (4*quad channel only)
    gskill ripjaws4 2800 4*4*

    example true ram for ryzen and all other amd
    geil evo x 3200 2*8
    or
    gskill RGB trident z 3200 2*8

    NOTE=true slot ??? in AMD you must put ram in exact slot , according your motherboard user manual , so before put ram on ramslot see your mobo true ram slot (wrong slot can make system cant start or crash )


    in amd ram is very very very sensetive ,but if you use no1 best ram, you never see even 1 freeze,bluescreen or freeze hang in 1 year !!

  9. #9
    ROG Enthusiast Array
    Join Date
    Aug 2017
    Reputation
    10
    Posts
    73

    850P2!

    Please keep us posted as I have a 1200P2 and facing a different but somewhat similar issue in that my PSU doesn't get signaled to turn off the system. I can power it on though all day long.

    YOUR LIGHTS GO ON when you plug in the motherboard, what about your fans? Do your CPU fans also start spinning? IF SO THIS MAYBE EXACTLY THE SAME ISSUE I HAVE.

    I'm trying to figure out if there is some kind of incompatibility between the SuperNOVA series and the Zenith extreme - wondering if the Erp stuff getting in the way.

    Also, make sure you try another PSU if you have access to one.
    Last edited by pisymbol; 10-05-2017 at 02:31 PM.

  10. #10
    ROG Enthusiast Array
    Join Date
    Aug 2017
    Reputation
    10
    Posts
    73

    Quote Originally Posted by IM3CPO View Post
    That video is so funny. I WISH screw #1 was that easy to tighten. Holy cow.

Page 1 of 5 1 2 3 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •