AI Suite 3 Version 3.00.10 & 3.00.13 - user test/report thread

[Runit]

I have an 850 evo.. not super sure what M.2 nvme is. Though some games are on the ssd and some are on another harddrive but they all have the hitching so I don't think thats the problem.

m.2 is a pcie conector type so you have a sta ssd or a pcei or a m.2
but you problem could also be that your spu overclock is bad try resetting the bios and if you have 2 monitors try looking at the cpu usage in the taks man
i have seen mine dowing weerd stuff aswel lik it using 1 thread at 100% and the other just running 6%

but it could also be the storge aldo if you have a sdd it seems unlikly

[Phrawst]

m.2 is a pcie conector type so you have a sta ssd or a pcei or a m.2
but you problem could also be that your spu overclock is bad try resetting the bios and if you have 2 monitors try looking at the cpu usage in the taks man
i have seen mine dowing weerd stuff aswel lik it using 1 thread at 100% and the other just running 6%

but it could also be the storge aldo if you have a sdd it seems unlikly

Why would it be fine after a reboot though?

[Runit]

Why would it be fine after a reboot though?

well i had similar problems about half a year ago then after mutch thinkering with the ai suite overclock settings i got a stable overclock then it all ran very wel until i got a blue screen 2 days ago and i had to clr the cmos to get a game pad to work again and it reset the stable overclock i had and i stil had to fix ai suit after the update and now its all crap again
i had the same thing wher it ran fine then when the pc was left on for a few days it got crapy and since i always leave the pc on

[KEyBAD]

I got random sensor corruption (seems to go from C6H, because with no software i have same strange temp/fan/voltage results)

When trying to enter DIGI+ section


DIP5 is 1.05.13

[Pottypotsworth]

I just tried v3.00.13 downloaded from the Maximus VIII Impact Motherboard page, and as per the beta I still cannot get anything other than a blank screen from AiSuite 3.

I've tried using AiCleaner in safe mode but all it does is pop up really quickly so I don't even know if it is working properly.

I don't have any sort of exotic setup, i can't really understand why the software isn't just working?

[Runit]

I just tried v3.00.13 downloaded from the Maximus VIII Impact Motherboard page, and as per the beta I still cannot get anything other than a blank screen from AiSuite 3.

I've tried using AiCleaner in safe mode but all it does is pop up really quickly so I don't even know if it is working properly.

I don't have any sort of exotic setup, i can't really understand why the software isn't just working?

its normal for the aicleaner to pop up quick it is rly fast it just removes some files from some folders
also ther is a dip5 1.05.14

KEyBAD you can also try this aldo it also dont work right atleast for me i think it eve cousing my pc to reboot during the night now ....
here is the link

also looking at your pic it almost looks like your missing the dip 5 mabe that is the problem

[g.tse]

@ Asus

Thanks for the update, glad to have the program up & running again. I only use it for fan curves (I much prefer it over the bios setup as it also allow me to set my AIO pump speed).

However, I now have a small problem.

Program used to work fine up until a couple of days ago.
I just switched 3 fans on my rig and as it should the fan tuning wizard asked me to re-configure.
Fan curvs were set up just fine but the problem is that now, after every reboot it ask me to re-configure the fans, plus it does not keep my saved profile.

Can someone assist? Thanks!

edit: forgot to add that my mobo is the Crosshair VI Hero.

[Jackalito]

@ Asus

Thanks for the update, glad to have the program up & running again. I only use it for fan curves (I much prefer it over the bios setup as it also allow me to set my AIO pump speed).

However, I now have a small problem.

Program used to work fine up until a couple of days ago.
I just switched 3 fans on my rig and as it should the fan tuning wizard asked me to re-configure.
Fan curvs were set up just fine but the problem is that now, after every reboot it ask me to re-configure the fans, plus it does not keep my saved profile.

Can someone assist? Thanks!

edit: forgot to add that my mobo is the Crosshair VI Hero.

I have your same mobo and it's working fine for me, though I haven't changed any case fans. I'm using v3.00.10. Are you using the same version? How did you proceed to install it?

[Samuel Scsa]

does not work properly on the motherboard Maximus VII Formula, therefore, it does not identify the coolers and does not overclock the processor.

[ankhazam]

does not work properly on the motherboard Maximus VII Formula, therefore, it does not identify the coolers and does not overclock the processor.

on my M7F I'm using the old version....